ElCap
Nomad
Posts: 281
Registered: 1-22-2010
Location: Montara CA, or San Ignacio BCS
Member Is Offline
|
|
Broke down in San Ignacio - need auto part delivered
After decades of traveling to Baja in Landcruisers and Tacomas, this time I came down in a 2006 Sprinter van. Evidently this can problematic down
here!
Anyhow, I am comfortably (in a safe place with everything I need) broken down here in San Ignacio, trying to sort out an intermittent electrical
starting problem. I want to get the van back safely across the border sooner than later, and there's a good chance I will need a part that is not
available down here (yes I know there is a MB dealer in La Paz). So I'm putting out the word to my fellow Nomads - if anyone here is either driving
thru central Baja or flying to Loreto in the next few days to week and would be willing to bring a part (small fuse block) down, please get back to me
here, or by U2U. Gracias!!
|
|
|
4x4abc
Ultra Nomad
Posts: 4283
Registered: 4-24-2009
Location: La Paz, BCS
Member Is Offline
Mood: happy - always
|
|
tell us exactly which part you need
large Sprinter community in La Ventana and Los Barriles
someone might have it
MB dealers in Los Cabos and La Paz usually don't have parts
everything is ordered and takes a long time
I waited 3 months once - and they sent the wrong part
Harald Pietschmann
|
|
|
ElCap
Nomad
Posts: 281
Registered: 1-22-2010
Location: Montara CA, or San Ignacio BCS
Member Is Offline
|
|
Thanks. I believe the part I need is fuse block#1 - located below steering column - for a 2006 Freightliner Sprinter 2500. Still attempting to
determine that this is what i need - I've got a few Sprinter friends currently trying to decipher my symptoms. I'll post a part# if/when I have one.
It looks like part is about $150 new - surprising cheap for what it does?
|
|
|
ElCap
Nomad
Posts: 281
Registered: 1-22-2010
Location: Montara CA, or San Ignacio BCS
Member Is Offline
|
|
Part Number: 30465-05824642 Fuse box w/fuses
|
|
|
bajatrailrider
Super Nomad
Posts: 2431
Registered: 1-24-2015
Location: Mexico
Member Is Offline
Mood: Happy
|
|
Is Baja Pac a option ? ABC brings me parts when I have no other way
|
|
|
boe4fun
Super Nomad
Posts: 1040
Registered: 1-22-2006
Location: Margaritaville
Member Is Offline
Mood: Circling the drain........
|
|
I’m in Bahía Asunción now, will leave for La Paz this Wednesday. It’s probably a long shot, but I could stop in at the big refracciones auto
shop/store in Vizcaino. If you’re certain of the part number it won’t hurt to ask! U2U me with your name, contact information, where currently
located and I’ll see what I can do Wednesday morning on my way south. Suerte.
Two dirt roads diverged in Baja and I, I took the one less graveled by......
Soy ignorante, apático y ambivalente. No lo sé y no me importa, ni modo.
|
|
|
mjs
Nomad
Posts: 309
Registered: 2-20-2013
Location: Off grid in San Felipe
Member Is Offline
|
|
Are there current sensors or electronic control components inside the fuse box? If not and it's just a simple fuse block you should be able to bypass
any circuits or even the whole box using readily available parts from AutoZone.
Not elegant but a way to get home. If OTOH it is a Power Distribution Module, that's a bit more difficult.
|
|
|
surfhat
Senior Nomad
Posts: 537
Registered: 6-4-2012
Member Is Offline
|
|
The Sprinter Source forum site is invaluable, especially with its members generosity in helping to answer everything Sprinter van related whenever
asked.
Good luck getting the parts you need. There is lots to learn about Sprinters and their owners avoiding the dealerships when possible.
A great resource in the San Diego area for parts and service is the Sprinter Pitstop off of Miramar Rd. Using genuine factory parts is their norm.
You can count on them to be treated fair.
|
|
|
ElCap
Nomad
Posts: 281
Registered: 1-22-2010
Location: Montara CA, or San Ignacio BCS
Member Is Offline
|
|
Thanks to all for your comments and suggestions. And yes the Sprinter-Source forum is invaluable - going to do some sleuthing today with a
multimeter, hopefully will find some joy!
|
|
|
BajaBlanca
Select Nomad
Posts: 13195
Registered: 10-28-2008
Location: La Bocana, BCS
Member Is Offline
|
|
I bet they can fed ex the part to you. It may cost a bundle but it can be done!
|
|
|
Hook
Elite Nomad
Posts: 9009
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
Two things I would recommend.
One-find the location of every engine block ground that is on the block itself. Remove all wires, wire brush them clean, wire brush the block surface
where they attach and re-attach. Do the same for the ground lead to the battery. This is especially important if the valve covers have been leaking
oil down the sides of the block to where the engine grounds are.
Two-disconnect each and every ECM (engine control module) multipin connector from the ECMs (my 2005 Wrangler has four), spray the pins with electrical
contact cleaner and re-attach, making sure they are well seated. ECMs are usually mounted on the firewall between the engine compartment and the cab
of the vehicle.
These ECM connectors will probably have the common Chrysler locking mechanisms where you slide a red tab from one position to the next, then depress
the release and pull on the connector. Be sure to re-attach, including sliding the red locking tabs back into place.
My 2005 Jeep began to start throwing OBD codes over a months timespan (oil pressure sender) and the speedometer began failing which also rendered the
cruise control inoperative. The most likely fix for the speedo was the VSS (velocity speed sensor) but replacing that inexpensive part did not fix the
speedo/CC. But these ailments happened closely enough in time that I began to wonder if something was impeding the electrical signal to these sensors.
So I performed the tasks I recommended above and it/they fixed both problems. Not sure which task fixed it but from trouble shooting boat electrical
problems, I always start with checking grounds.
Has anyone put an OBD II reader on it yet? Or, have you tried turning the key off and on (not turning the engine over, just on and off) in rapid
succession? Many Chrysler products of that era would display the trouble code where the electronic odometer displays mileage, after doing that.
OBD codes can be VERY specific about the problem, sometimes. My Jeep started running really rough and the codes indicated the SPECIFIC fuel injector
that had failed. I replaced them all since the engine has over 100k on it, and it fixed the problem.
A good OBD reader might tell you exactly what is going on. Is an engine warning light or check engine light staying on?
[Edited on 3-28-2022 by Hook]
|
|
|
ElCap
Nomad
Posts: 281
Registered: 1-22-2010
Location: Montara CA, or San Ignacio BCS
Member Is Offline
|
|
Thanks all. I found the part at Carlsbad MB and a Nomad has reached out and will be delivering the part on Friday. Hopefully it will do the trick. In
the meantime I am still troubleshooting/testing electrical components - the van will run great, just need to get past the starting issue. Meanwhile
I’ll enjoy where I am.
|
|
|
Hook
Elite Nomad
Posts: 9009
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
Before your delivery guy leaves the States, take us through your logic in deciding that it was this fuse block. Did a trouble code indicate this?
Is the vehicle turning over but not starting or is it not even turning over? Does it only occur when it the engine is hot, is shut off, and then it
won't start?
|
|
|
JZ
Select Nomad
Posts: 10385
Registered: 10-3-2003
Member Is Online
|
|
I have a 2015 Silverado HD.
For the last 6 months every once in a blue moon I turn the key and the starter just sort of clicks but doesn't crank. Turn it again and it is fine.
Had some work don't on the diesel exhaust system about a week ago.
Using just my description, the mechanic said the most likely problem is the chip in the key is failing. Yet to be confirmed, so we'll see.
|
|
|
Cancamo
Nomad
Posts: 357
Registered: 4-5-2011
Member Is Offline
|
|
"Meanwhile I’ll enjoy where I am".
In the early 80's my transmission went out in La Paz. Over the next couple of weeks waiting for parts and repairs to get done I walked all over town.
Got to know the town and it's neighborhoods quite well. This was when nobody locked their doors and front porches were filled every evening. Super
friendly and inviting Pacenos, was the norm, often sharing food and drink in their homes.
A lasting impression and fond memories of the city.
"Wherever you go, there you are"
|
|
|
JC43
Nomad
Posts: 498
Registered: 6-21-2014
Member Is Offline
|
|
What about ordering the part NOB? Those main MB dealers do have most parts in stock. But look for a dealer which has Sprinters for sale. Shipping
to MX should not be a problem. Mailboxes etc. is pretty fast in shipping to MX. Just an idea.
|
|
|
4x4abc
Ultra Nomad
Posts: 4283
Registered: 4-24-2009
Location: La Paz, BCS
Member Is Offline
Mood: happy - always
|
|
Quote: Originally posted by Cancamo  | "Meanwhile I’ll enjoy where I am".
In the early 80's my transmission went out in La Paz. Over the next couple of weeks waiting for parts and repairs to get done I walked all over town.
Got to know the town and it's neighborhoods quite well. This was when nobody locked their doors and front porches were filled every evening. Super
friendly and inviting Pacenos, was the norm, often sharing food and drink in their homes.
A lasting impression and fond memories of the city.
"Wherever you go, there you are"
|
man, I remember that old La Paz
now it is Cabo on steroids
sure, everything changes - but I am stunned how fast it went downhill
LA PAZ QUE SE PERDIO
Harald Pietschmann
|
|
|
![[*]](images/xmbforum/default_icon.gif){kind=icon}
