BajaNomad
Not logged in [Login - Register]

Go To Bottom
Printable Version  
Author: Subject: Fuse issues on an E-tec
Santiago
Ultra Nomad
*****




Posts: 3499
Registered: 8-27-2003
Member Is Offline


[*] posted on 11-3-2018 at 04:42 PM
Fuse issues on an E-tec


2005 50 HP Etec
Last trip the engine started normally but the tach (Faria system check) needle wildly swung around and the lights would flicker. At full throttle engine ran normally and the tach would move to clearly wrong positions; trolled for an hour and pulled into a shallow cove for lunch, turned the engine off. 30 minutes later it would not crank and the tilt/trim would not work; all accessories worked.
We were in 2' of water so I jumped in and walked around to the motor; the trim switch on the motor would not work. I wiggled the cables/wiring and the trim switch work. Motor started and we hightailed it back to the ramp - the tach was not working at all, sat on zero.
Next day the motor would not crank and tilt was dead, accessories working. Had power to the negative side of the starter and the positive side of the relay where the battery cables are attached.
I decided to check the fuse and the fuse holder seemed a little loose, not really connected tightly where it snaps to the side of the plastic cover of the flywheel. When I turned the holder to the side so I could pull the fuse, the fuse fell out of it's own weight. I retrieved the fuse and it was good, put it back it and everything worked fine. Unclipped the fuse holder, turned it upside down and gave it a few hard shakes - fuse staid in, did not shake out. Ran the boat all over the lake and tach was normal, motor fine.
How or why would a fuse work its way out of the holder and would a barely-in fuse cause the tach to wildly swing around the light to flicker?

I've posted this on an E-tec board, monitored by mechanics, as it may be something unique to this engine. The fuse is a 10amp blade type, not in-line glass.

View user's profile
caj13
Senior Nomad
***




Posts: 998
Registered: 8-1-2017
Member Is Offline


[*] posted on 11-3-2018 at 08:50 PM


vibration is my best guess. remember those old electric football games in the 6os that moved guys by vibrating the playing field.
possible the fuse wasnt originally fully inserted. yeah the fuse vibrating in the holder, as the ends of the blades worked their way out were causing rapid "on off" of current flow

[Edited on 11-4-2018 by caj13]
View user's profile
woody with a view
PITA Nomad
*******




Posts: 15937
Registered: 11-8-2004
Location: Looking at the Coronado Islands
Member Is Offline

Mood: Everchangin'

[*] posted on 11-4-2018 at 07:04 AM


Wouldnt you see signs of arcing if it was that loose? Ive heard similar gremlin type stories that turned out to be a bad ground. Check them all.

Edit: spell check

[Edited on 11-4-2018 by woody with a view]




View user's profile
ncampion
Super Nomad
****




Posts: 1238
Registered: 4-15-2006
Location: Loreto
Member Is Offline

Mood: Retired and Loving it

[*] posted on 11-4-2018 at 02:23 PM


Do you have a wiring diagram? What does that fuse protect? May be unrelated, but possible vibration caused it to disengage or become intermittent. Unlikely that it would cause everything except acc. to go dead. I agree with woody, first check all battery wiring including grounds. E-techs are highly electronic, hope you can find the problem. It's usually something simple (hopefully).



Living Large in Loreto. Off-grid and happy.
View user's profile

  Go To Top

 






All Content Copyright 1997- Q87 International; All Rights Reserved.
Powered by XMB; XMB Forum Software © 2001-2014 The XMB Group






"If it were lush and rich, one could understand the pull, but it is fierce and hostile and sullen. The stone mountains pile up to the sky and there is little fresh water. But we know we must go back if we live, and we don't know why." - Steinbeck, Log from the Sea of Cortez

 

"People don't care how much you know, until they know how much you care." - Theodore Roosevelt

 

"You can easily judge the character of others by how they treat those who they think can do nothing for them or to them." - Malcolm Forbes

 

"Let others lead small lives, but not you. Let others argue over small things, but not you. Let others cry over small hurts, but not you. Let others leave their future in someone else's hands, but not you." - Jim Rohn

 

"The best way to get the right answer on the internet is not to ask a question; it's to post the wrong answer." - Cunningham's Law







Thank you to Baja Bound Mexico Insurance Services for your long-term support of the BajaNomad.com Forums site.







Emergency Baja Contacts Include:

Desert Hawks; El Rosario-based ambulance transport; Emergency #: (616) 103-0262