| Pages:
1
2 |
surfer jim
Super Nomad
Posts: 1891
Registered: 8-29-2003
Location: high desert
Member Is Offline
|
|
rubber truck bed liner....?
I will be putting a rubber liner under my truck camper if/when I remove it...where can I get one locally?....(Orange-San Berdu countys)....
|
|
|
Tomas Tierra
Super Nomad
Posts: 1281
Registered: 3-23-2005
Location: oxnard, ca
Member Is Offline
Mood: Tengo Flojera
|
|
seems like just about any camper shell outlet will have these...a MUST for underneath the pop up..I can't remember if you bolt through the bed of your
truck or not, if so, when you cut holes in your rubber liner make them BIG..it is a pain in the culo to line them up properly...
|
|
|
BajaWarrior
Super Nomad
Posts: 2307
Registered: 9-27-2006
Location: Mission Bay, San Diego. Playa Hermosa, San Felipe.
Member Is Offline
Mood: Anxious to get south
|
|
Kragens Auto parts, Pep Boys, Napa, etc...
Haven't had a bad trip yet....
|
|
|
Hook
Elite Nomad
Posts: 9010
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
Give it a good stiff scrubbing with a good detergent after you get one. They seem to be some form of very uncured rubber and it really can smell
bad.........almost noxious. It dissipates SLOWLY but you will smell it through your storage compartments that empty into the bed of the truck.
Some trimming may be necessary but I have never had to cut holes in one for any reason. You certainly dont want anything even as low profile as a
carriage bolt head underneath your popup. Just rubber on the bottomside.
|
|
|
TacoFeliz
Nomad
Posts: 266
Registered: 7-22-2005
Location: Here
Member Is Offline
Mood: Exploratory
|
|
I've had great results with a WolfLiner spray-in bedliner done at their place in Corona off the 91 freeway. $300 complete, super-clean job, done in
about an hour and a half, quarter inch plus and pretty bulletproof. Also quiets the noise transmission from the steel truckbed. Works well under the
4Wheeler pop-top.
|
|
|
Hook
Elite Nomad
Posts: 9010
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
| Quote: | Originally posted by TacoFeliz
I've had great results with a WolfLiner spray-in bedliner done at their place in Corona off the 91 freeway. $300 complete, super-clean job, done in
about an hour and a half, quarter inch plus and pretty bulletproof. Also quiets the noise transmission from the steel truckbed. Works well under the
4Wheeler pop-top. |
WoW thats a really good price if it is anything like a Rhinoliner job.
|
|
|
surfer jim
Super Nomad
Posts: 1891
Registered: 8-29-2003
Location: high desert
Member Is Offline
|
|
Thanks for the tips.....
|
|
|
bigzaggin
Nomad
Posts: 441
Registered: 5-27-2004
Member Is Offline
Mood: way too ites
|
|
Jim...
one note on the spray-on bed-liner - and I might not have seen every variety - but most tend to have a really "gritty" surface which is not friendly
to surfboards (and I'm guessing you might be a surfer?). The spray-on liners are certainly a tighter "fit" but rubber can A.) Be removed B.) Is
suitably non-slip (w/o being abrasive) and C.) Is, for the most part, cheaper.
I'm sure both serve a purpose, but I prefer rubber.
|
|
|
TMW
Select Nomad
Posts: 10659
Registered: 9-1-2003
Location: Bakersfield, CA
Member Is Offline
|
|
I've had a sprayin liner on my last 3 trucks. I really like them over the plastic ones. I also use a rubber mat in the bed. Not as slippery. If you
get the spray in liner get the ultra violet protection. It keeps a shine to it otherwise they fade and become dull from the sun. I've had both Rhino
and Arma and I am happy with both. Since I carry motorcycles I put a steel bar (1 inch square tube) across the front at the top and bolt it to the
front of the bed before they spray it. It keeps the bed from bending out especially in the center.
|
|
|
Hook
Elite Nomad
Posts: 9010
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
Guys, we're talking about a base for a slide-in camper.
|
|
|
Tomas Tierra
Super Nomad
Posts: 1281
Registered: 3-23-2005
Location: oxnard, ca
Member Is Offline
Mood: Tengo Flojera
|
|
| Quote: | Originally posted by Hook
I have never had to cut holes in one for any reason.
I bolted through the floor of my camper and the bed of the truck(consequently my rubber mat as well). my small original holes would only line up if
mars was in a certain position. so I cut big holes |
|
|
|
Hook
Elite Nomad
Posts: 9010
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
So, T.T.
you have to do a full-on ratchet job from underneath to remove your camper?
No tanks.........I'd sooner use the turnbuckles on the outside.
|
|
|
Bruce R Leech
Elite Nomad
Posts: 6796
Registered: 9-20-2004
Location: Ensenada formerly Mulege
Member Is Offline
Mood: A lot cooler than Mulege
|
|
I don't have one of these campers so I don't understand why the rubber? what happens if you don't use it?
Bruce R Leech
Ensenada
 |
|
|
Diver
Ultra Nomad
Posts: 4729
Registered: 11-15-2004
Member Is Offline
|
|
They slide around !!
|
|
|
Bruce R Leech
Elite Nomad
Posts: 6796
Registered: 9-20-2004
Location: Ensenada formerly Mulege
Member Is Offline
Mood: A lot cooler than Mulege
|
|
seems like the bolts through the floor would fix that
Bruce R Leech
Ensenada
|
|
|
Diver
Ultra Nomad
Posts: 4729
Registered: 11-15-2004
Member Is Offline
|
|
You can get away without a mat but the friction does help stop the movement even with bed bolts.
I mounted a 10' camper in a bed with a Rhinoliner and it moved a bit on the hard plastic surface with my outrigger tie-downs and turnbuckles.
|
|
|
Tomas Tierra
Super Nomad
Posts: 1281
Registered: 3-23-2005
Location: oxnard, ca
Member Is Offline
Mood: Tengo Flojera
|
|
Hook...
It is a pain in the boot getting under the truck every time but it keeps me on a more personal basis with my steed..actually my camper is not the
exact fit for the truck and doesn't leave enough room for turn buckles and such.
It is nice to know I can go as hard as I want without coming loose..also I straightened out the eye bolt/turnbuckle set up with my old truck once..a
testament to the strenght of the 4 wheel pop up camper!
[Edited on 10-19-2006 by Tomas Tierra]
|
|
|
Bruce R Leech
Elite Nomad
Posts: 6796
Registered: 9-20-2004
Location: Ensenada formerly Mulege
Member Is Offline
Mood: A lot cooler than Mulege
|
|
thanks guys I am learning something new
Bruce R Leech
Ensenada
|
|
|
jerry
Super Nomad
Posts: 1354
Registered: 10-10-2003
Location: loreto
Member Is Offline
|
|
my bro uses rubber mats that are used inside horse trailers there about 1 inch thick he uses them over the top of the sprayin liner makes a great
cousuion
jerry and judi
|
|
|
Hook
Elite Nomad
Posts: 9010
Registered: 3-13-2004
Location: Sonora
Member Is Offline
Mood: Inquisitive
|
|
| Quote: | Originally posted by Tomas Tierra
Hook...
It is a pain in the boot getting under the truck every time but it keeps me on a more personal basis with my steed..actually my camper is not the
exact fit for the truck and doesn't leave enough room for turn buckles and such.
It is nice to know I can go as hard as I want without coming loose..also I straightened out the eye bolt/turnbuckle set up with my old truck once..a
testament to the strenght of the 4 wheel pop up camper!
[Edited on 10-19-2006 by Tomas Tierra] |
I see your points.
With the Happy Jack system, they give you these hard rubber guides that look alot like nun buoys on the water. They have bolts running in the middle
of them. The idea is that you mount these in the bed about 1 inch outside the footprint of a camper. There is also a set for the bed wall between the
cab and the bed. Idea is it limits your shifing to no more than an inch IF the turnbuckles dont hold it in place..........which they often wont on a
dirt road.
|
|
|
| Pages:
1
2 |
![[*]](images/xmbforum/default_icon.gif){kind=icon}
