| Pages:
1
2 |
Santiago
Ultra Nomad
Posts: 3512
Registered: 8-27-2003
Member Is Offline
|
|
Cutting a block wall
[img] [/img]
I'm going to put a 6068 sliding glass door where the 4030 window is, centered below the V-shape above. Eventually this stepped area that is filled
with cardon strips will be glass block (some weight). The deck/roof load is NOT on this wall as the joists run in the same direction as this wall.
I've never worked with block and my question is this: how would you cut the block? I have a worm-drive skill saw and I was going to use a 7-1/4"
masonry blade and make cuts on the exterior and interior sides of the wall. But I also have a 4" angle grinder and I could use that.
1. Which is best?
2. Will use some used 6X6 PT as header and king studs. This seem reasonable?
3. Here's the tricky part: can I make the 2 side cuts and one vertical cut at the top and remove the entire 7'X7' at one time or should I do it in
two 3.5'X7'sections; then remove one section and brace the top and then remove the other? There is very little weight above the window at this time.
[Edited on 12-28-2009 by Santiago]
|
|
|
Debra
Super Nomad
Posts: 2101
Registered: 10-31-2002
Location: Port Orchard Wa./Bahia de Los Angeles BC
Member Is Offline
|
|
Won't that glass block make it that much more hot for sleeping up there in the summer (If you do that) Just a thought........
Your place is looking great BTW, glad to hear you are almost finished, you know where you can start next when you get bored right?  
Mean people suck!
|
|
|
capt. mike
Elite Nomad
Posts: 8085
Registered: 11-26-2002
Location: Bat Cave
Member Is Offline
Mood: Sling time!
|
|
can you borrow or rent a gas powered makita with a carbide mas blade, aka cut off saw.
that's what i'd get, wear goggles.
we used one to make all the changes to the door and windows locations at the Lopez Mateo Flying Sams clinic when we did a make over to that old CMU
school building.
cuts like butter.
formerly Ordained in Rev. Ewing\'s Church by Mail - busted on tax fraud.......
Now joined L. Ron Hoover\'s church of Appliantology
\"Remember there is a big difference between kneeling down and bending over....\"
www.facebook.com/michael.l.goering |
|
|
Santiago
Ultra Nomad
Posts: 3512
Registered: 8-27-2003
Member Is Offline
|
|
Mike: I might be able to get one. You think making one big 7' wide cut is OK? I feel a little funny about making the cuts and then beating on the
blocks with a sledge and then having the blocks above fall in.
|
|
|
Ken Bondy
Ultra Nomad
Posts: 3326
Registered: 12-13-2002
Member Is Offline
Mood: Mellow
|
|
This is probably a dumb question, but there are literally hundreds of US companies, big and small, that specialize in cutting and coring concrete and
masonry. They do it with diamond sawblades/cores and specialized saws/drills. Any chance there is anyone with that type of equipment where you are?
You are describing some pretty intricate work, I am assuming you have 8" CMU (concrete masonry units), if so the 7'x7' section is going to weigh more
than 4,000 pounds if it is fully grouted. You prepared to handle that?
carpe diem!
|
|
|
comitan
Ultra Nomad
Posts: 4177
Registered: 3-27-2004
Location: La Paz
Member Is Offline
Mood: mellow
|
|
If you cut the opening and install the patio door where you plaster to fill to the door, it will crack later, the best way is to knock it out and
refill the much greater area with plaster. The reason is you fill to a straight cut edge you don't have a good surface for the plaster, when you
plaster to a jagged edge you have a lot more area for the plaster to stick. Hope I'm clear.
Strive For The Ideal, But Deal With What\'s Real.
Every day is a new day, better than the day before.(from some song)
Lord, Keep your arm around my shoulder and your hand over my mouth.
“The sincere pursuit of truth requires you to entertain the possibility that everything you believe to be true may in fact be false”
|
|
|
DENNIS
Platinum Nomad
Posts: 29510
Registered: 9-2-2006
Location: Punta Banda
Member Is Offline
|
|
| Quote: | Originally posted by Santiago
how would you cut the block? I have a worm-drive skill saw and I was going to use a 7-1/4" masonry blade and make cuts on the exterior and interior
sides of the wall. But I also have a 4" angle grinder and I could use that.
1. Which is best?
2. Will use some used 6X6 PT as header and king studs. This seem reasonable?
3. Here's the tricky part: can I make the 2 side cuts and one vertical cut at the top and remove the entire 7'X7' at one time or should I do it in
two 3.5'X7'sections; then remove one section and brace the top and then remove the other? There is very little weight above the window at this time.
|
You'll probably end up using both those saws with diamond blades. Carbide and concrete don't mix well.
Do you know what kind of header is over the existing window? If it's concrete and steel, you have your work cut out for you. You can hope it's
wood. Whatever it is, it's holding up all the weight over the opening, the block wall, and according to the foto, there's a lot of that. It needs
to be supported if you remove the header.
|
|
|
DENNIS
Platinum Nomad
Posts: 29510
Registered: 9-2-2006
Location: Punta Banda
Member Is Offline
|
|
| Quote: | Originally posted by Ken Bondy
if it is fully grouted. |
My guess is that it wouldn't be solid based on Mexico building methods. Bond beams, columns and maybe headers only.
|
|
|
Russ
Elite Nomad
Posts: 6742
Registered: 7-4-2004
Location: Punta Chivato
Member Is Offline
|
|
Easy... mostly. You can cut both inside and out but not really necessary. You can just bust out the block with a sledge since you'll want the opening
a little bigger than your frame. 4x material will be strong enough but I'd go at least a wide as the walls. Cement the rough opening and put 3 J bolts
on each side and two for the header. I'd tar the inside of each member to help detour bugs. The sill has to be cement to carry the load so take your
time with that and make it's wider and stronger than the wood frame (rebar & or wire). Just to be on the safe side support the roof until you have
your frames set.
Bahia Concepcion where life starts...given a chance!
|
|
|
Russ
Elite Nomad
Posts: 6742
Registered: 7-4-2004
Location: Punta Chivato
Member Is Offline
|
|
The header over the windows on my place are at the same height as the door and they poured a beam all the way around at that height. If that's the
case you could just use 2x to frame with. Maybe no header.
Bahia Concepcion where life starts...given a chance!
|
|
|
k-rico
Super Nomad
Posts: 2079
Registered: 7-10-2008
Location: Playas de Tijuana
Member Is Offline
|
|
Won't rebar be a problem?
If you hit some, how do you cut that stuff?
Also, isn't a header of some sort needed across the full span of the opening, and then some? Would a 4x6 wood beam work?
|
|
|
Ken Bondy
Ultra Nomad
Posts: 3326
Registered: 12-13-2002
Member Is Offline
Mood: Mellow
|
|
Santiago: Just some unsolicited advice from an old structural engineer: The "header" you and others are talking about (also commonly called a
"lintel") is a beam that spans across your new opening and supports all the wall weight above it, including the weight of the wall and any tributary
floor and roof loads that span to the wall. I realize that your deck/roof joists run parallel to the wall, nonetheless the wall will pick up some
small tributary deck/roof loads. Make sure that your new lintel can handle that load with the new 7'+ span. If you are not comfortable designing and
building that lintel yourself, have someone with experience look at it. It will ruin your whole weekend if your new lintel collapses into the new
opening.
carpe diem!
|
|
|
wessongroup
Platinum Nomad
Posts: 21152
Registered: 8-9-2009
Location: Mission Viejo
Member Is Offline
Mood: Suicide Hot line ... please hold
|
|
Hey, which ever way you go, take pictures.. of what you do, have seen the before, would like to see the after.... and what you used and the steps you
take.. someone else could use the "experience" gained from your work..... should open the place up a bit.. good luck.. these are fun projects, at
least I used to like them...
I'm with Russ, it shouldn't be too bad... doesn't look like a lot of wall and roof, but I'm here and your there... 
[Edited on 12-29-2009 by wessongroup]
|
|
|
Santiago
Ultra Nomad
Posts: 3512
Registered: 8-27-2003
Member Is Offline
|
|
Thanks guys:
Ken: I have some rough 6X6 pressure treated DF. I was going to use that as the new header and support with same 6X6 on each side. In other words,
my rough opening in the block would be 12" wider than the door and 6" taller.
However, I think Russ may have hit on something. The cabin was built using 16" square block columns at the 4 corners of a 11'X22' rectangle. I seem
to recall my landlord saying once that the header above the kitchen door (not in this photo) goes all the way around the structure and the block below
is simply fill.
And no, I'm not prepared to deal with 4000 pounds.
|
|
|
Diver
Ultra Nomad
Posts: 4729
Registered: 11-15-2004
Member Is Offline
|
|
Here are my thoughts;
1. Measure the height from the inside slab to the top of the window opening. Most sliders require 80 - 80 1/2". Check the slider you are planning to
use; some manufacturers have slightly differing heights. If the height is sufficient then you are WAY ahead of the game.
If not, you would have to remove part of the actual header in which case you would want to remove more; enough for a new wood header above the current
opening. If this is the case, I would punt and go with a 3' wide, hinged glass door cut to your opening height.
2. If #1 above was easy, start by cutting the top at bith sides at the currect height with a diamond blade in a worm drive (if you use a wet blade,
you will have to water the area while cutting).
3. Make the vertical cuts where you want them, on both sides all the way to the top cut. Use a small hand sledge or better yet, an electric chipping
hammer or rotohammer. As you chip, you may run into rebar or wire cages that can be cut with a sawzalll or angle grinder. Lay some plywood to protect
the inside floor and hammer from the inside if possible.
If you remove reinforcing, you will probably want to make some effort to replace the "effect" of the reinforcing. Once the wall sections are removed,
chip out the inside webs of the vertical blocks on each side of the opening enough to install a #4 rebar, vertically into this space and grout it to a
smooth opening. You should install at least 3 anchors on each side of the openiing (lags with washers or 1/2" J-bolts) to hold the 2x min. sub-frame.
A similar method can be used of the header if it is not filled with grout; otherwise, fill what you can, add rebar where you can, and rotohammer some
anchors to hold your head framing.
If you immerdiately install the pressure-treated sub-frame, you can brace it until the mortar dries to ensure a good fit. If you want to waterproof
before stucco, try "RedGuard" or similar liquid tile underlayment waterproofer.
Make sure to use a heavy bead of urethane caulk under either door upon installation to avoid leaks.
The more I think wbout it, the more I think I would go for the 3' wide glass door.
Good Luck !!
.
|
|
|
dtbushpilot
Ultra Nomad
Posts: 3288
Registered: 1-11-2007
Location: Buena Vista BCS
Member Is Offline
Mood: Tranquilo
|
|
| Quote: | If you are determined to do it yourself get a good gas-powered rotary saw with a masonry blade and go balls to the wall. |
Be sure to keep them away from the rotating saw blade ....dt
"Life is tough".....It's even tougher if you're stupid.....
|
|
|
msawin
Nomad
Posts: 371
Registered: 8-29-2003
Location: Grass Valley,Ca / Tripui
Member Is Offline
|
|
Santiago,
plan ahead. Cut back to the width of the cardon. floor to roof. You have enough width for mason / rebar jambs ,header. Go for a 6/10 height and you
can fly with a 6/8 0r 6/9 or 6/10 height door. easy in fill 0n head. do a top header at the roof line. mason with steel rebar. you can get ,we sell a
block frame aluminum window that excepts vinyl block or glass block. many colors and you can make a pattern with the block patterns available. you can
get venting block windows also. casement and awning style..also you can get an aluiminum vinyl block window custom height if you do a slider above..
great for venting. we have done many of these above tubs in homes..size of the block windows is based on the the block size. you can not believe how
much heat comes thru the block windows if that is an issue. I'll see if I can attach a photo of a couple of glass block windows we used in our Baja
spot..
marty
|
|
|
Santiago
Ultra Nomad
Posts: 3512
Registered: 8-27-2003
Member Is Offline
|
|
| Quote: | Originally posted by msawin
Santiago,
plan ahead. Cut back to the width of the cardon. floor to roof. You have enough width for mason / rebar jambs ,header. Go for a 6/10 height and you
can fly with a 6/8 0r 6/9 or 6/10 height door. easy in fill 0n head. do a top header at the roof line. mason with steel rebar. you can get ,we sell a
block frame aluminum window that excepts vinyl block or glass block. many colors and you can make a pattern with the block patterns available. you can
get venting block windows also. casement and awning style..also you can get an aluiminum vinyl block window custom height if you do a slider above..
great for venting. we have done many of these above tubs in homes..size of the block windows is based on the the block size. you can not believe how
much heat comes thru the block windows if that is an issue. I'll see if I can attach a photo of a couple of glass block windows we used in our Baja
spot..
marty |
Good points: I was thinking of doing just that - remove all the block from the top of the cordons down to the bottom, put the header at the top and
fill in - did not think of heat build up with the glass block and as this wall gets the afternoon sun it would be a killer. Will need to re-think
that point. I already have the blocks thru Craig's List; 8X8X4.
|
|
|
oladulce
Super Nomad
Posts: 1625
Registered: 5-30-2005
Location: bcs
Member Is Offline
|
|
Yes, photos please. And what did you decide to do with your front door Santiago? Have you tackled that project yet?
|
|
|
shari
Select Nomad
Posts: 13048
Registered: 3-10-2006
Location: bahia asuncion, baja sur
Member Is Offline
Mood: there is no reality except the one contained within us "Herman Hesse"
|
|
When we wanted our back door and big windows...it was pretty crazy to watch juan swing that sledgehammer...kinda looked like he was enjoying it
too...hmmm. I was surprised how quick it got knocked down and makes much less dust...look forward to the pics amigo.
|
|
|
| Pages:
1
2 |
![[*]](images/xmbforum/default_icon.gif){kind=icon}
